Festiva (BP) MS2 V3 Wiring, please check over my homework
Hello all. Could you check over my wiring and tell me if there is anything I need to change, or where I need fuses. I am planning to run all wires that need to go to a 12v source through the same main fuse on my fuse block. Other than that I don't have any. I am pretty sure the TPS isn't wired right
I am using a DIYAUTOTUNE.COM base harness and splicing my plugs onto it.
1. F-idle wire - Not being used at this time
2. 4 IAC wires on harness - Not being used
3. IAT (Orange on MS harness) to IAT sensor, other wire from sensor plug to ground
4. Fuel pump (Purple on MS harness) to Fuel pump relay in car
5. Pink "o2" wires goes to Zeitronix wideband o2 output wire
6. Coil - Brown (MS harness) Ign Output wire to negative side of coil plug, other side of coil plug goes to 12volt source
__________________________________________________ _________
__________________________________________________ _________
7. 8 prong plug (only 7 wires on plug) Fuel Injectors, TPS, and Coolant
ONLY ON FESTIVA I BELIEVE THE PLUG ON THE PROTEGE IS DIFFERENT
TPS (I have a 4 plug TPS and throttle body, need the plug before I can change the below)
1. TPS Signal(Blue) to Yellow/Black (Festiva color) Idle
2. TPS vref (grey) to yellow (Festiva color) "WOT"
3. Ground to Ground black (festiva color)
4. leave unattached - 4th wire on protege automatic tps
COOLANT PLUG
1. Coolant (yellow) to Red/Blue (festiva color) positive side of plug
2. Ground - black (festiva color) negative side of plug
FUEL INJECTORS
INJ #1 and INJ #3 Green/Black to (MS harness -blue) Inj #1
INJ #2 and INJ #4 Green/Yellow to (MS hanress -green) Inj #2
All injectors wired to Yellow/Black goes to 12 volt source
__________________________________________________ ______
__________________________________________________ ______
8. DISTRIBUTOR
1. Black/Green (protege color) (BLACK on fesitva) to GROUND
2. White/Red (protege color) (Yellow/Black on festiva) to 12 volt source
3. White (protege color) (Yellow/BLUE on festiva) to Ignition Input "shield"
4. 4th wire (home) leave unattached (yellow/blue on PROTEGE).
I am using a DIYAUTOTUNE.COM base harness and splicing my plugs onto it.
1. F-idle wire - Not being used at this time
2. 4 IAC wires on harness - Not being used
3. IAT (Orange on MS harness) to IAT sensor, other wire from sensor plug to ground
4. Fuel pump (Purple on MS harness) to Fuel pump relay in car
5. Pink "o2" wires goes to Zeitronix wideband o2 output wire
6. Coil - Brown (MS harness) Ign Output wire to negative side of coil plug, other side of coil plug goes to 12volt source
__________________________________________________ _________
__________________________________________________ _________
7. 8 prong plug (only 7 wires on plug) Fuel Injectors, TPS, and Coolant
ONLY ON FESTIVA I BELIEVE THE PLUG ON THE PROTEGE IS DIFFERENT
TPS (I have a 4 plug TPS and throttle body, need the plug before I can change the below)
1. TPS Signal(Blue) to Yellow/Black (Festiva color) Idle
2. TPS vref (grey) to yellow (Festiva color) "WOT"
3. Ground to Ground black (festiva color)
4. leave unattached - 4th wire on protege automatic tps
COOLANT PLUG
1. Coolant (yellow) to Red/Blue (festiva color) positive side of plug
2. Ground - black (festiva color) negative side of plug
FUEL INJECTORS
INJ #1 and INJ #3 Green/Black to (MS harness -blue) Inj #1
INJ #2 and INJ #4 Green/Yellow to (MS hanress -green) Inj #2
All injectors wired to Yellow/Black goes to 12 volt source
__________________________________________________ ______
__________________________________________________ ______
8. DISTRIBUTOR
1. Black/Green (protege color) (BLACK on fesitva) to GROUND
2. White/Red (protege color) (Yellow/Black on festiva) to 12 volt source
3. White (protege color) (Yellow/BLUE on festiva) to Ignition Input "shield"
4. 4th wire (home) leave unattached (yellow/blue on PROTEGE).