Announcement

Collapse
No announcement yet.

95 626 CEL codes? and Probinator chip

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    #16
    those codes wouldnt cause a power loss like that. your looking at other issues. im betting your timing is off.
    ~PaTricK~


    -Current car's-
    ~ 92 Probe GT Turbo, 90 FE3 Turbo 626GT hatch, 97 KL mtx 626, 05 Mazda6, 09 Kia Sportage V6~
    What are you driving?

    Comment


      #17
      Oh, well great... Read somewhere that the chip would fix the driveability issues because changes air/fuel ratio... God I hope so

      Comment


        #18
        it will def run better then it would on the american spec ecu on ZE engine. but even without the chip, and on the stock ecu, you should still have a 14 sec car in your hands. the car will still run just fine and have ALOT of power on the original ecu.

        since your saying you have no top end. that says something else is definitely wrong. the ZE pull even harder top end. if you have no top end, thats a pretty basic sign that your engine probably skipped timing.
        ~PaTricK~


        -Current car's-
        ~ 92 Probe GT Turbo, 90 FE3 Turbo 626GT hatch, 97 KL mtx 626, 05 Mazda6, 09 Kia Sportage V6~
        What are you driving?

        Comment


          #19
          Well here's the deal, try to floor it from a dig and it'll bog almost always. Shift to second an pin it it'll bog as well. If slowly go through the gears it's problem free. Then after go to idle after driving hard it struggles to catch itself and drops to 300rpms or dies completely... Timing?

          Comment


            #20
            The chip from factory started with a 3xxxx and I read a 16xxx or 2xxx meant something but nothing about a 3... So it's getting soldered now and see what happens when put in car I guess

            Comment


              #21
              Definitely sounds like your ignition timing is off...any issues with cold starts or running it cold?
              -Jack

              ONTARIO MAZDA CLUB! Join! https://www.facebook.com/groups/500055016671733/

              91 626 LX - basically stock and pretty slow still
              http://www.clubprotege.com/forum/sho...my-GD-626-LX-)

              01 E53 3.0i - FOR SALE! pm if interested

              91 USDM Protege LX - SOLD! turbo/manifold up for sale!
              http://www.clubprotege.com/forum/showthread.php?t=46606

              Comment


                #22
                starts just fine and if dont touch the gas itll idle fine to... i cant time so ill have to have a shop do it. is there a "degree" i should have it set to? or do i tell the shop to "make it run right" lol

                Comment


                  #23
                  10 degrees, vehicle has to be in diagnostics mode to set any base settings. Same procedure as the BP
                  -Jack

                  ONTARIO MAZDA CLUB! Join! https://www.facebook.com/groups/500055016671733/

                  91 626 LX - basically stock and pretty slow still
                  http://www.clubprotege.com/forum/sho...my-GD-626-LX-)

                  01 E53 3.0i - FOR SALE! pm if interested

                  91 USDM Protege LX - SOLD! turbo/manifold up for sale!
                  http://www.clubprotege.com/forum/showthread.php?t=46606

                  Comment


                    #24
                    im talking the timingbelt timing. it sounds like you skipped a tooth. it will still run and idle like normal. and all you need to do is remove the plastic timing covers, and make sure the lines on the pulleys are lined up with the marks on the engine. thats it.
                    ~PaTricK~


                    -Current car's-
                    ~ 92 Probe GT Turbo, 90 FE3 Turbo 626GT hatch, 97 KL mtx 626, 05 Mazda6, 09 Kia Sportage V6~
                    What are you driving?

                    Comment


                      #25
                      havnt gotten the bp running yet so havnt screwed with the timing at either lol. but how do i put in diagnostic mode? i can snag a timing light to check if i read in a Haynes how to do so. I've never touched timing on anything and actually scares me some lol

                      Comment


                        #26
                        ive seen marks on my bp, so on this it literally needs to just lign up? any way to get pic of said marks from anyone?

                        Comment


                          #27
                          there won't be any write ups on here for that really...you'll have to search MX6.com for the write up. It's like the BP just not as easy to see the crank pulley.
                          -Jack

                          ONTARIO MAZDA CLUB! Join! https://www.facebook.com/groups/500055016671733/

                          91 626 LX - basically stock and pretty slow still
                          http://www.clubprotege.com/forum/sho...my-GD-626-LX-)

                          01 E53 3.0i - FOR SALE! pm if interested

                          91 USDM Protege LX - SOLD! turbo/manifold up for sale!
                          http://www.clubprotege.com/forum/showthread.php?t=46606

                          Comment


                            #28
                            borrowing a timing light this weekend hopefully and seeing how it goes. from what im told its use the timing lite and adjust via the distributor? works for me if that easy

                            Comment


                              #29
                              yeppers, as long as you know how to properly operate the gun and inspect timing it won't be much of a task...just wedging the timing gun in there can be fun...
                              -Jack

                              ONTARIO MAZDA CLUB! Join! https://www.facebook.com/groups/500055016671733/

                              91 626 LX - basically stock and pretty slow still
                              http://www.clubprotege.com/forum/sho...my-GD-626-LX-)

                              01 E53 3.0i - FOR SALE! pm if interested

                              91 USDM Protege LX - SOLD! turbo/manifold up for sale!
                              http://www.clubprotege.com/forum/showthread.php?t=46606

                              Comment


                                #30
                                find out if i do or not this weekend lol

                                Comment

                                Working...
                                X