I felt a real nice improvement when I went from a smic to fmic.
Announcement
Collapse
No announcement yet.
1st Gens 1990 4WD work log
Collapse
This is a sticky topic.
X
X
-
1993 Protege LX-Midnight's shadow SOLD
1996 Honda CBR600-Wrecked. Damn Honda crippled me
2002 mazda MPV-family truckster SOLD
2010 VW routon
Originally posted by jay.....they totally underestimated the number of gearheads such as myself that have families but refuse to grow the hell up and stop playing with cars, or that otherwise see the utility of having 4 doors. Obviously I ain't alone, as there are a helluva lotta sti and evo here. Bueler? Beuler? Mazda? Mazda?
-
It's hard to tell until I'm driving the 4WD. I will need some suspension upgrades to round out the package though.
My next power mod will be a power move. I've got my son's Uni loans that I'll be paying on for a while but, if the planets align, and if Mazda changes that stupid smiley grill on the MP3,
That means I'll be selling the BG's and all hardware that goes with them. Not yet though. Maybe a couple years.
I felt a real nice improvement when I went from a smic to fmic.Last edited by 1st Gen; 10-15-2010, 08:14 PM.1991 Protege LX with GTX swap, DD1990 4WD Protege with GTX swap, Project/garage decoration2006 Mazda 3 with 2.3, Her car1980 Ford F100 Short bed with 300ci 6 cylinder, work truck/home for moss
Comment
-
Originally posted by 1st Gen View PostThat means I'll be selling the BG's and all hardware that goes with them.1990 Protege 4WD
GT-X BP26 swap [AT->MT]|Cup holder cut to fit|Synthetic gear oil|Synthetic brake fluid|Corksport SS brake/clutch lines|Mazdaspeed HV oil pump|GT-X front STB|Corksport type I rear STB|Matching full-size spare wheel|Homebrew Brass shifter bushing|Speed Source brass shifter cable bushings|EDM headlights/corners|FMIC|EDM cabin vents
1 3 5
├┼┤
2 4 R
Seeking: Canadian 4WD seatbelts.
Comment
-
I fulfilled my resolution of working on the project at least some every day by buying some hose clamps for the intercooler and researching the plug for the pressure regulator. Sometimes, "some" is the best I can do.1991 Protege LX with GTX swap, DD1990 4WD Protege with GTX swap, Project/garage decoration2006 Mazda 3 with 2.3, Her car1980 Ford F100 Short bed with 300ci 6 cylinder, work truck/home for moss
Comment
-
I got most of the SMIC hooked up today. Not a big thing but it puts me a little farther down the road. The coupler pieces were pretty stiff so I soaked them in hot water to soften them up a bit. So far so good. I have one piece I'm a concerned about but am going to use it and see if it holds up. It should be okay.
I'm still having harness issues. The fuel pressure regulator doesn't have a dedicated plug for it but I do have a few pieces that will fit it. There are some other plugs too.
I probably shouldn't post this yet but I can't seem to figure this out.1991 Protege LX with GTX swap, DD1990 4WD Protege with GTX swap, Project/garage decoration2006 Mazda 3 with 2.3, Her car1980 Ford F100 Short bed with 300ci 6 cylinder, work truck/home for moss
Comment
-
The doesn't answer my questions but it does give me some terminology to think about.
Well, the wires that seem to be available for this aren't the right color.
It looks like I can splice into the w/r wire, but then it goes to the em harness, somewhere. A ground perhaps.Last edited by 1st Gen; 10-18-2010, 12:42 AM.1991 Protege LX with GTX swap, DD1990 4WD Protege with GTX swap, Project/garage decoration2006 Mazda 3 with 2.3, Her car1980 Ford F100 Short bed with 300ci 6 cylinder, work truck/home for moss
Comment
-
Still need to do
Walbro fuel pump install
install gauge cluster and as much of the interior as I have time for
attach slim fan to radiator and install (found out the fasteners aren't long enough, have to source better solution)
finish the SMIC piping and install VAF
inspect harness thoroughly and finish install
inspect all vacuum lines and replace as necessary
buy boost gauge
buy muffler and high flow cat
think about some type of MP3 player and speakers
think about motor mounts and if I want to throw in with AWR
figure out head liner
pick up seat belt latches at j/y
I had assumed that the trans had no oil in it when I went to fill it so when it only took half the amount it was supposed to, it kind of created a problem, as well as a mess. Decide whether I'm going to drain the oil out so I can make sure the Royal Purple is the only oil in there. I'm more pissed about this than anything. RP ain't cheap!
inspect chassis harness plugs and decide what was supposed to go to the air conditioning and how I'm going to bind those wires up, figure out which plugs I need to replace or otherwise fix, and just reinstall everything.
install new headlight bulbs and make sure all those fixtures are secure
inspect bumper and decide if and how I want to mod that mess
source some fender well inserts
Keep an eye out for 15" aluminum wheels
buy new lug nuts for bling
Edit-
(done)Figure out Trans oil thing (never under estimate my own stupidity and laziness)
(done)New clutch master cylinder and bleed that system
(done)buy new battery and figure out battery box
(done)install GTX down pipe to turbo exhaust (I'm not sure if there is a risk of having the turbo vent so close to the turbine but I'm going to take a chance)Last edited by 1st Gen; 10-21-2010, 11:03 PM.1991 Protege LX with GTX swap, DD1990 4WD Protege with GTX swap, Project/garage decoration2006 Mazda 3 with 2.3, Her car1980 Ford F100 Short bed with 300ci 6 cylinder, work truck/home for moss
Comment
-
Clutch master cylinder replaced and clutch bled. It was pretty darned satisfying to push that clutch in and feel the mechanism work. Same for the brakes.
In the Mazda harness W/R wires are 12V. Ground wires are black or brown.
idk when. it should have gone a long time ago. the whole interior got moldy and there is some body damage on the passengers side.
Actually, fender well inserts, the under engine protective cover, and maybe some other body parts. Let me know when and where and I'm there.Last edited by 1st Gen; 10-20-2010, 10:10 PM.1991 Protege LX with GTX swap, DD1990 4WD Protege with GTX swap, Project/garage decoration2006 Mazda 3 with 2.3, Her car1980 Ford F100 Short bed with 300ci 6 cylinder, work truck/home for moss
Comment
Comment