If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
can it go 180? thought it could only go in one way. Also the plug wires are for sure in the right order. it has spark just doesn't try to fire off it like basicly floods itself.
Not 180°, but it could be 60° or 120° off. The cam gears have two slots for the dowel pin (some even have three). The intake cam needs to be in the slot aligned with the 'I' and the exhaust in the slot aligned with the 'E'. If it didn't have multiple slots, Mazda would have to make specific gears for each cam.
Not 180°, but it could be 60° or 120° off. The cam gears have two slots for the dowel pin (some even have three). The intake cam needs to be in the slot aligned with the 'I' and the exhaust in the slot aligned with the 'E'. If it didn't have multiple slots, Mazda would have to make specific gears for each cam.
--Ferdi
OH i thought you were talking about the disty sorry yes ryan did the timing and he says there in the right spot.
My baby 93' Protege Lx--R.I.P
New Baby 94' Protege Lx Black
91' Miata - SOLD
93' Protege LX new Project (no rust)!
Mods: Protege: Engine: Suspension: Exterior: Audio:
sigpic
Makes me wonder about valve/tappet clearance to the cam lobes. Granted, HLA's should make it right, but if the stem height is too big, the valves could be not closing all the way. And being a non-interference engine, you can't tell.
we haven't done one yet sarge...... & come to think of it. steve did lose some valves & we purchased replacements...... however we never compared the old ones to the new ones side/side to see if any were longer........
im getting one today and going to test them if thats the issue i found the old valves and im going to take the head off and then have those 4 put back in, although back on page 1 looking at the head I CAN"T TELL what ones were the new ones ****ty but they all look like they are sealing, im going to try like i said puting more ground to the motor then if that doesn't change anything im going to do the compression test.
Last edited by madtownmazda; 09-24-2010, 11:36 AM.
My baby 93' Protege Lx--R.I.P
New Baby 94' Protege Lx Black
91' Miata - SOLD
93' Protege LX new Project (no rust)!
Mods: Protege: Engine: Suspension: Exterior: Audio:
sigpic
these are the pistons i used so i hope these rings that wisco supplied aren't screwed
Attached Files
My baby 93' Protege Lx--R.I.P
New Baby 94' Protege Lx Black
91' Miata - SOLD
93' Protege LX new Project (no rust)!
Mods: Protege: Engine: Suspension: Exterior: Audio:
sigpic
im guessing you're running the bp26 ecu? what about trying to hook up the n/a ecu to see if it'll pull any codes???
i had issues with my 323 due to a bad distributor, changed it and still wouldnt start, turned out to be fuel lines were crossed lol. so don't sweat it man!
you've spent this much time and effort on the engine! now you just have to spend some time to get her running! don't think of it as this POS won't run! Think of it as my ****ing sweet mazda needs some more time to get everything in tune so you can ass rape other cars!!!! hahaha.
heres where the cams and crank are set on N/A with the exintake
Attached Files
My baby 93' Protege Lx--R.I.P
New Baby 94' Protege Lx Black
91' Miata - SOLD
93' Protege LX new Project (no rust)!
Mods: Protege: Engine: Suspension: Exterior: Audio:
sigpic
Ferdi sent me this so!!! i think i figured it out!!!
Attached Files
My baby 93' Protege Lx--R.I.P
New Baby 94' Protege Lx Black
91' Miata - SOLD
93' Protege LX new Project (no rust)!
Mods: Protege: Engine: Suspension: Exterior: Audio:
sigpic
think i figured it out me and bpt323 when i first turbo'd the car with the exintake cam we had to make new marks on the cam gears since if you take an exhaust cam and put it in the intake look at the loabs there the SAME so i needed to flip it almost 180 degrees not quite tho heres the marks we made!
also more pics but computer is being a
last pic is for Ferdi There ya go! show ya what i mean?
Attached Files
Last edited by madtownmazda; 09-24-2010, 05:43 PM.
My baby 93' Protege Lx--R.I.P
New Baby 94' Protege Lx Black
91' Miata - SOLD
93' Protege LX new Project (no rust)!
Mods: Protege: Engine: Suspension: Exterior: Audio:
sigpic
Comment