GB: Pierce Motorsports front strut bars

[JPmotorsports]

I will make a note about every ones answer on the first post for you Jim if you want.

Thanks James---after seeing how many people have camber plates, it's not going to be much work at all---I have like 4 that aren't clearanced, so those will go to the Ksport/coilover guys.

[MazdaNoob]

stock mounts here

[bogaut]

hey jim, your inbox is full.

running a bg protege with a bp, and ksports, so there shouldnt be any clearance issues. address is 12345 sw 121st ave Tigard, Oregon 97223. yea lemme know what the total will be with shipping and ill get you the rest of the payment ASAP. thanks for all your hard work!

[JPmotorsports]

hey jim, your inbox is full.

running a bg protege with a bp, and ksports, so there shouldnt be any clearance issues. address is 12345 sw 121st ave Tigard, Oregon 97223. yea lemme know what the total will be with shipping and ill get you the rest of the payment ASAP. thanks for all your hard work!

Sorry about that---I've cleared out some room---I'll get you a quote tomorrow-talk soon!

[Iantboyd]

Stock mounts.

PM me when you are ready for final payment and shipping address.

[JPmotorsports]

Hey Guys--Happy New Year---just got back in today and the first three are nearly done---we welded up the first one and built the jig---and we're just confirming measurements---it's a good fit on this car so we're checking some other's before we start welding up the rest and shipping. If anyone has Ksports and has an extra minute if they wouldn't mind taking an exact measurement from the front inner strut mount stud to stud---it comes to a point---and get me a measurement across the top center point to center point. Should be around 39 3/8"ish...Thanks.

[CODY004WD]

Ahhh! I'm getting so excited! Eyeballing it, I am going to bet $15 that this will fit a 1.9L SEFI, and I'll even bet $5 that it's within 1/4" (if not less) of fitting The KL with a Millenia Manifold. I have plans of Moving the KL back 1" on my next swap, so I think that I can also drop the motor a smidge, and be A-Okay with this bar. If not I have plans to make it fit.

If there is anyway that the rear bar could raise up 1/4" vs shooting so far forward, I have no doubt it would fit. It would make sense that the hood would likely clear this, since the rake of the hood is so extreme in these things, but I dunno? I think the Brake Reservoir would still be easily accessible too.

Input?

[concealer404]

Uh oh... This might not clear on my car. I'll take measurements tomorrow.

I'll take measurements across the towers as well.

[JPmotorsports]

Uh oh... This might not clear on my car. I'll take measurements tomorrow.

I'll take measurements across the towers as well.

Don't worry---I'll adjust the height for the different needs---just looking for the width at the moment---the first 3 aren't needing anything special. We'll get everyone handled no matter what it takes!

[JPmotorsports]

Ahhh! I'm getting so excited! Eyeballing it, I am going to bet $15 that this will fit a 1.9L SEFI, and I'll even bet $5 that it's within 1/4" (if not less) of fitting The KL with a Millenia Manifold. I have plans of Moving the KL back 1" on my next swap, so I think that I can also drop the motor a smidge, and be A-Okay with this bar. If not I have plans to make it fit.

If there is anyway that the rear bar could raise up 1/4" vs shooting so far forward, I have no doubt it would fit. It would make sense that the hood would likely clear this, since the rake of the hood is so extreme in these things, but I dunno? I think the Brake Reservoir would still be easily accessible too.

Input?

Absolutely---I did one today and I raised the back up almost 1/2"---we'll make sure it'll be available to anyone/any config if it's possible...

[CODY004WD]

Awesome! I bet that one would fit my needs for sure.

[bogaut]

patiently waiting

[MazdaNoob]

I want mine signed!

[KAinjection]

I will get the measurement tomorrow Jim, I was doing side work all day.....

[Mazda_Powered]

Uh oh... This might not clear on my car. I'll take measurements tomorrow.

I'll take measurements across the towers as well.

comparing pictures it looks like the foward bar will sit right above your rear bank fuel rail, I think it'll work!

I want mine signed!

cool idea!! could charge more for the "signature series" lol