ok, Ive tried searching some, but figured Id go ahead and post up my exact problems
Just got Lex's MSII a few days ago, went out today trying to get it all hooked back up and running
ill start by saying hooked up it cranks and idles fairly well, i then hook up the vacuum line to the ecu and it idles fairly low
When i open Megatune 2.25 i get
"Controller code version does not match signature in Megasquirt-I.int(See audit.log for where the above file was found"
"expected 0x14
recieved 0x51
Table corruption may occur, terminate MegaTune now?"
if i click no it pops up the screen of 8gauges all reading zero,
"Although the file was read sucessfully there were 243warnings written to audit.log file, you may want to review.....send&burn values into controller?"
**I am debating going outside and clicking yes with MS plugged in
i think im having trouble with my serial to USB cord be recognized on my laptop, possibly why they continue to all read 0 after i crank the car
when i open MSII download 1.04 i get
"For MS-II:
1) Short the "B/LD" jumper on the MS-II board.
2) Power cycle MS-II.
3) File->Open."
I was given a different screen the first time i opened it but cant get that screen up again
MegaLog Viewer opens i assume just fine, but stays blank
When i crank the car the center led on the ECU lights up, and the first one flashes, when i give it gas the third lights up
there are 2 files in the Firmware folder that dont open
"megasquirt-II.ini.2.873"
"Monitor_v2.873.abs"
I apolagize if this a repost of anykind, I havent been able to find this info, and my laptop took a dump on my this weekend so im using a buddys till monday and would like to have all this figured out when it comes time to reload it all on my computer
Thanks guys!
ps. I realize this is all inexperience problems I am not by anymeans trying to attack Lex or his services, work done looks great and the car runs as is...just damn confussing software
Just got Lex's MSII a few days ago, went out today trying to get it all hooked back up and running
ill start by saying hooked up it cranks and idles fairly well, i then hook up the vacuum line to the ecu and it idles fairly low
When i open Megatune 2.25 i get
"Controller code version does not match signature in Megasquirt-I.int(See audit.log for where the above file was found"
"expected 0x14
recieved 0x51
Table corruption may occur, terminate MegaTune now?"
if i click no it pops up the screen of 8gauges all reading zero,
"Although the file was read sucessfully there were 243warnings written to audit.log file, you may want to review.....send&burn values into controller?"
**I am debating going outside and clicking yes with MS plugged in
i think im having trouble with my serial to USB cord be recognized on my laptop, possibly why they continue to all read 0 after i crank the car
when i open MSII download 1.04 i get
"For MS-II:
1) Short the "B/LD" jumper on the MS-II board.
2) Power cycle MS-II.
3) File->Open."
I was given a different screen the first time i opened it but cant get that screen up again
MegaLog Viewer opens i assume just fine, but stays blank
When i crank the car the center led on the ECU lights up, and the first one flashes, when i give it gas the third lights up
there are 2 files in the Firmware folder that dont open
"megasquirt-II.ini.2.873"
"Monitor_v2.873.abs"
I apolagize if this a repost of anykind, I havent been able to find this info, and my laptop took a dump on my this weekend so im using a buddys till monday and would like to have all this figured out when it comes time to reload it all on my computer
Thanks guys!
ps. I realize this is all inexperience problems I am not by anymeans trying to attack Lex or his services, work done looks great and the car runs as is...just damn confussing software
Comment