What did you do to your BF today???

[jjmundt]

Completely stock. The injectors have been in the car for about 5 years

Hmmm...I've got some thinking to do...

You running stock fuel pump and FPR? I've got a Walbro pump for an RX-7 as well as the FPR from an RX-7.

Regards,
Joel

[noshatch]

TurboII fuel pump and stock regulator. I also have all the fuel cut off vac lines disabled if that makes any difference but I dont think it does

[riverrunnernky]

I ordered.....

Mazdaspeed rear trailing arms for my Hatchback,

Does anyone know where I can find tophats for my rear coils??

[bighed323]

cleaned up the engine a bit.

[Kelso]

bout to pull the b6t out and start the evo conversion!

[noshatch]

Tried another ecu thats chipped and the car runs richer and breaks up. So yeah stock ecu with turbo II injectors is the way for me. I just ordered a new clutch today and the tach adapter for my msd and I will hopefully be racing it on oct 4th at the import event

[Rustypro]

Tried another ecu thats chipped and the car runs richer and breaks up. So yeah stock ecu with turbo II injectors is the way for me. I just ordered a new clutch today and the tach adapter for my msd and I will hopefully be racing it on oct 4th at the import event

if u racing i gotta get in this..(if i can get slicks by then) how much to race? in what class?

[Rustypro]

hey Matt.....FYI that ecu belongs in my car... damn tony

[noshatch]

if u racing i gotta get in this..(if i can get slicks by then) how much to race? in what class?
hey Matt.....FYI that ecu belongs in my car... damn tony

Well its $45 to race. I pick up my clutch today and the msd stuff im missing. I wish that I had slicks but i am going on street tires. O and yeah it was your computer that I tried and the map on it is for stock injectors and not my injectors. I need to find out what software was used on the chip so I can tune it myself. It ran too rich under boost and it was breaking up. It read 10.0 on the a/f meter and thats at 15psi

[FamiliaGT]

Better to be rich then lean.

[riverrunnernky]

BF to GTX upgrade......

GTX Upgrade to my BF Non-Turbo hatchback....

I can't wait to get the struts back on and see the difference in ride.

I think I'll do a how to thread or work log on this subject.

[noshatch]

Where did you get the trailing arms from??? Mine are getting bad and I am going to have to change them.

Yesterday I worked on the car all day. Put the clutch in, Put the MSD in and played with the timing a lil bit. I am having a problem with the MSD that I think is a ground problem. The car shuts off if I put any load on the battery. I am going to try and figure it out today

[FamiliaGT]

Got a call from my engine builder about my build. He said he needed wrist pin bushings. I search everywhere, no one, even Mazda has them separately. Mazda's the only company that even has them, but you have to buy all new rods to get them. What bull****! What if someone needs a set for their engine rebuild? Your **** out of luck if it happens. So, I might be buying brand new mazda B6T rods here real soon. On the upside, I gots new rods!

[trailrider098]

Got a call from my engine builder about my build. He said he needed wrist pin bushings. I search everywhere, no one, even Mazda has them separately. Mazda's the only company that even has them, but you have to buy all new rods to get them. What bull****! What if someone needs a set for their engine rebuild? Your **** out of luck if it happens. So, I might be buying brand new mazda B6T rods here real soon. On the upside, I gots new rods!

Might. As well just pay for a set of gtr rods from corksport, I imagine that NOS b6t rods prob cost as much

[riverrunnernky]

The oem trailing arms....

Where did you get the trailing arms from??? Mine are getting bad and I am going to have to change them.

Yesterday I worked on the car all day. Put the clutch in, Put the MSD in and played with the timing a lil bit. I am having a problem with the MSD that I think is a ground problem. The car shuts off if I put any load on the battery. I am going to try and figure it out today

are only a dealer item so far as I have found.
$59. plus tax. from the dealer.

I got Corksport Mazdaspeed GTX and had bushings made to fit a shoulder bolt and tapped the strut to fit the bolt.

The Mazdaspeed arms cost me abt. $75. So in all that cost is about $150.

The Mazdaspeed arms are a heavier made than the oem. However they are not the exact fit and bushings will have to be fabricated of a high grade metal. I used hydraulic pipe to make it on a lathe.

I can't wait to get the coil spring 'top hats' to complete this project.